jeudi 5 septembre 2013

Installation & Configuration de WVIEW - Votre Station Météo connectée via le Raspberry PI

Installation & Configuration de Wview 

sur un Raspberry PI

Temps d'installation entre 50 et 90 minutes.


ETAPE 0 - download Raspbian (armhf)
Downloader ce torrent ou utilisez le lien direct suivant download et placé le sur une SDCARD d'au minimum 2 Go


ETAPE 1 - Placer les repositories

$ sudo nano /etc/apt/sources.list ou $ sudo vi /etc/apt/sources.list
deb http://mirrordirector.raspbian.org/raspbian/ wheezy main contrib non-free rpi
deb-src http://mirrordirector.raspbian.org/raspbian/ wheezy main contrib non-free rpi


$ sudo apt-get update


ETAPE 2 - installation

Maintenant, vous pouvez soit utiliser un script d'installation ou faire une installation "manuelle"



Méthode avec le script d'installation ( méthode recommandée )
$ wget http://goo.gl/yiaz0 -O wview-install-raspbian.sh
$ chmod +x wview-install-raspbian.sh ; ./wview-install-raspbian.sh


Méthode "manuelle"
$ sudo apt-get install --yes build-essential zlib1g-dev libpng12-dev libreadline-dev gawk libsqlite3-dev sqlite3 libgd2-xpm libgd2-xpm-dev libssl-dev sendmail sendemail libcurl4-openssl-dev libusb-1.0-0 libusb-1.0-0-dev apache2 php5 php5-sqlite libapache2-mod-php5 ntp tnftp wget
$ wget http://downloads.sourceforge.net/radlib/radlib-2.12.0.tar.gz
$ tar zxvf radlib-2.12.0.tar.gz
$ cd radlib-2.12.0
$ ./configure --enable-sqlite --prefix=/ --bindir=/usr/bin --sysconfdir=/etc --localstatedir=/var/lib --libdir=/usr/lib
$ sudo make install
$ cd ..


$ wget http://downloads.sourceforge.net/wview/wview-5.20.2.tar.gz
$ tar zxvf wview-5.20.2.tar.gz
$ cd wview-5.20.2
$ ./configure --prefix=/ --bindir=/usr/bin --sysconfdir=/etc --localstatedir=/var/lib --libdir=/usr/lib
$ sudo make install
$ cd ..


$ sudo wget http://goo.gl/H13iS -O /etc/init.d/wview
$ sudo chmod +x /etc/init.d/wview
$ sudo update-rc.d wview defaults 99
$ sudo ln -s /var/lib/wview/img/ /var/www/weather
$ sudo ln -s /var/lib/wviewmgmt/ /var/www/wviewmgmt



Si tout c'est bien passé, il faut maintenant configurer votre station météo
$ wviewconfig  ou http://your_raspi_ip/wviewmgmt (via votre navigateur préféré)



Vérification de votre configuration
$ wviewhtmlconfig


ATTENTION !! Avant de démarrer votre site WEB
$ sudo /etc/init.d/wview stop ; sudo rm /var/lib/wview/*.pid
$ sudo wviewcleardata



ETAPE 3 - un petit nettoyage

Effacement des fichiers inutiles
$ sudo rm -r radlib* ; sudo rm -r wview*
$ sudo apt-get clean




Etape 4 - Quelques réglages nécessaires :

Si vous désirez avoir le contrôle de wview pour effectuer un "Start/Stop" à partir de l'interface Web de Contrôle, (et que vous autorisez l'utilisateur du serveur web d'avoir les privilèges sudo), ajoutez l'utilisateur http au groupe sudo.

Ajouter l'utilisateur http au groupe sudo
$ sudo adduser www-data sudo
Modifier /etc/sudoers pour autoriser le contrôle "START/STOP"
$ sudo visudo ( Ajouter les lignes suivantes à la fin du fichier)
Cmnd_Alias WVIEW = /etc/init.d/wview
www-data ALL= NOPASSWD: WVIEW



ETAPE 5 - Configuration de wview 

PREREQUIS : 
  1. Avoir les coordonnées Longitude/Latitude de la station météo
  2. Avoir l'altitude en pieds ( via par exemple le site http://www.le-convertisseur.com/convertisseur-distances.html)
  3. Connaître le type de station Météo et comment elle se connecte (USB, RESEAU,  ...)
  4. Générer un password MD5 ( via par exemple le site http://www.cryptage-md5.com/)
  5. PRENDRE ATTENTION AUX PARAMETRES CI-DESSOUS EN ROUGE
  6. LES PARAMETRES EN BLEU SONT DONNES A TITRE D'EXEMPLE 
  7. LES PARAMETRES EN VERT SONT A RETENIR (DESTINATION DES FICHIERS) 

wviewconfig
root@raspberrypi:~# wviewconfig
################################################################################
 !!!!!!!!!!!!!!!!         READ THIS BEFORE PROCEEDING         !!!!!!!!!!!!!!!!

--> System Configuration for wview

--> Values in parenthesis are your existing values (if they exist) or defaults -
    they will be used if you just hit enter at the prompt...

--> Note: This script will save the existing wview-conf.sdb file to
          /etc/wview/wview-conf.old before writing the new file
          based on your answers here - if that is not what you want, hit CTRL-C now to
          abort this script!

################################################################################

pausing 3 seconds ...

-------------------------------------------------------------
Run template generator to generate web/other files from templates?
PARAMETER: ENABLE_HTMLGEN
(yes):
-------------------------------------------------------------
Run Alarm daemon to provide alarm script/client support?
PARAMETER: ENABLE_ALARMS
(no):
-------------------------------------------------------------
Run CWOP daemon to report station data to CWOP?
PARAMETER: ENABLE_CWOP
(no):
-------------------------------------------------------------
Run HTTP daemon to report station data to Weather Underground/Weather For You?
PARAMETER: ENABLE_HTTP
(no):
-------------------------------------------------------------
Run FTP daemon to transfer web site/generated files to a remote server?
PARAMETER: ENABLE_FTP
(no):
-------------------------------------------------------------
Run SSH daemon to transfer web site/generated files to a remote server?
PARAMETER: ENABLE_SSH
(no):
-------------------------------------------------------------
Run process monitor daemon to restart failed/hung daemons?
PARAMETER: ENABLE_PROCMON
(yes):
-------------------------------------------------------------
Station type - one of Simulator, Virtual, VantagePro, WXT510, TWI, WS-2300, WMR918, WMRUSB, WH1080, TE923:
PARAMETER: STATION_TYPE
(WMRUSB):
-------------------------------------------------------------
Physical interface to the weather station - one of serial or ethernet (usb is considered serial):
PARAMETER: STATION_INTERFACE
(serial):
-------------------------------------------------------------
Weather station serial device (/dev/ttyS0, /dev/ttyUSB0, etc.):
PARAMETER: STATION_DEV
(/dev/ttyUSB0):
-------------------------------------------------------------
Hostname or IP address (ethernet only):
PARAMETER: STATION_HOST
(10.10.10.10):
-------------------------------------------------------------
Host TCP port to the weather station (ethernet only):
PARAMETER: STATION_PORT
(22222):
-------------------------------------------------------------
Enable WeatherlinkIP interface:
PARAMETER: STATION_WLIP
(no):
-------------------------------------------------------------
Retrieve archive records from console (if no, they will be autogenerated):
PARAMETER: STATION_RETRIEVE_ARCHIVE
(yes):
-------------------------------------------------------------
Toggle DTR line during serial initialization:
PARAMETER: STATION_DTR
(yes):
-------------------------------------------------------------
Station rain season start month (1 - 12):
PARAMETER: STATION_RAIN_SEASON_START
(1):
-------------------------------------------------------------
Station rain storm start trigger (rainfall rate in inches/hour):
PARAMETER: STATION_RAIN_STORM_TRIGGER_START
(0.05):
-------------------------------------------------------------
Station rain storm stop time (hours without any rainfall which will end the storm):
PARAMETER: STATION_RAIN_STORM_IDLE_STOP
(12):
-------------------------------------------------------------
Station rain Year-To-Date preset (to include rain not in archive records) (x.yy inches):
PARAMETER: STATION_RAIN_YTD
(0):
-------------------------------------------------------------
Station ET Year-To-Date preset (to include ET not in archive records) (x.yyy inches, 0 disables):
PARAMETER: STATION_ET_YTD
(0):
-------------------------------------------------------------
Station rain/ET preset year (rain season start year that presets should apply to) (2000-present year, 0 disables):
PARAMETER: STATION_RAIN_ET_YTD_YEAR
(0):
-------------------------------------------------------------
Weather station elevation (feet above sea level):
PARAMETER: STATION_ELEVATION
(751): 524.96
-------------------------------------------------------------
Weather station latitude (decimal degrees, NORTH is positive - SOUTH is negative):
PARAMETER: STATION_LATITUDE
(33.6): 50.5
-------------------------------------------------------------
Weather station longitude (decimal degrees, EAST is positive - WEST is negative):
PARAMETER: STATION_LONGITUDE
(-96.9): 4.1
-------------------------------------------------------------
Weather data archive interval (minutes, one of 5, 10, 15, 30):
PARAMETER: STATION_ARCHIVE_INTERVAL
(5):
-------------------------------------------------------------
Weather station sensor poll interval (seconds) - should be divisor of 60:
PARAMETER: STATION_POLL_INTERVAL
(30):
-------------------------------------------------------------
Current conditions data push interval (seconds) - for wvalarmd and possibly others:
PARAMETER: STATION_PUSH_INTERVAL
(60):
-------------------------------------------------------------
Daemon Verbose Log Mask: 00000001 - wviewd,00000010 - htmlgend,00000100 - wvalarmd,00001000 - wviewftpd,00010000 - wviewsshd,00100000 - wvcwopd,01000000 - wvhttpd:
PARAMETER: STATION_VERBOSE_MSGS
(00000011):
-------------------------------------------------------------
Generate RX check data (populate rxCheck.png chart, VP only)?
PARAMETER: STATION_DO_RCHECK
(no):
-------------------------------------------------------------
Station Name:
PARAMETER: HTMLGEN_STATION_NAME
(changeme): BEL_LEROEULX
-------------------------------------------------------------
Station City:
PARAMETER: HTMLGEN_STATION_CITY
(changeme): LE ROEULX
-------------------------------------------------------------
Station State:
PARAMETER: HTMLGEN_STATION_STATE
(changeme): BELGIUM
-------------------------------------------------------------
Show interface details:
PARAMETER: HTMLGEN_STATION_SHOW_IF
(yes):
-------------------------------------------------------------
Where to store generated html and graphics files:
PARAMETER: HTMLGEN_IMAGE_PATH
(/usr/local/var/wview/img):
-------------------------------------------------------------
Where to find HTML template files:
PARAMETER: HTMLGEN_HTML_PATH
(/usr/local/etc/wview/html):
-------------------------------------------------------------
Generation start offset (0-4) in minutes:
PARAMETER: HTMLGEN_START_OFFSET
(0):
-------------------------------------------------------------
How often to generate (refresh interval for your site data) in minutes:
PARAMETER: HTMLGEN_GENERATE_INTERVAL
(1):
-------------------------------------------------------------
Enable metric conversion/units?
PARAMETER: HTMLGEN_METRIC_UNITS
(no): yes
-------------------------------------------------------------
If metric, use mm for rain instead of cm?
PARAMETER: HTMLGEN_METRIC_USE_RAIN_MM
(yes):
-------------------------------------------------------------
Default Wind Units:
PARAMETER: HTMLGEN_WIND_UNITS
(mph): kph
-------------------------------------------------------------
Display both metric and non-metric units on images?
PARAMETER: HTMLGEN_DUAL_UNITS
(yes):
-------------------------------------------------------------
Store/process extended sensor values?
PARAMETER: HTMLGEN_EXTENDED_DATA
(no):
-------------------------------------------------------------
How many daily archive record browser files to keep (-1 disables archive files, 0 indicates keep all, otherwise days to keep):
PARAMETER: HTMLGEN_ARCHIVE_BROWSER_FILES_TO_KEEP
(-1):
-------------------------------------------------------------
Moon 'increasing' text:
PARAMETER: HTMLGEN_MPHASE_INCREASE
(Waxing): Croissante
-------------------------------------------------------------
Moon 'decreasing' text:
PARAMETER: HTMLGEN_MPHASE_DECREASE
(Waning): Decroissante
-------------------------------------------------------------
Moon 'full' text:
PARAMETER: HTMLGEN_MPHASE_FULL
(Full): Pleine
-------------------------------------------------------------
Local Radar Image URL (no spaces):
PARAMETER: HTMLGEN_LOCAL_RADAR_URL
(http://www.srh.noaa.gov/radar/images/DS.p19r0/SI.kfws/latest.gif): http://www.buienradar.be/image/
-------------------------------------------------------------
Local Forecast URL (no spaces):
PARAMETER: HTMLGEN_LOCAL_FORECAST_URL
(http://www.wunderground.com/cgi-bin/findweather/getForecast?query=76233): http://belgique.lachainemeteo.com/meteo-belgique/ville/previsions-meteo-le-roeulx-88566-0.php
-------------------------------------------------------------
Date Format - see 'man strftime' for allowable formats; %D - US format mm/dd/yy, %d/%m/%Y  - dd/mm/yyyy, %x - locale's preferred date representation:
PARAMETER: HTMLGEN_DATE_FORMAT
(%x):
-------------------------------------------------------------
Barometer calibration multiplier:
PARAMETER: CAL_MULT_BAROMETER
(1.0):
-------------------------------------------------------------
Barometer calibration constant:
PARAMETER: CAL_CONST_BAROMETER
(0.0):
-------------------------------------------------------------
Station Pressure calibration multiplier:
PARAMETER: CAL_MULT_PRESSURE
(1.0):
-------------------------------------------------------------
Station Pressure calibration constant:
PARAMETER: CAL_CONST_PRESSURE
(0.0):
-------------------------------------------------------------
Altimeter calibration multiplier:
PARAMETER: CAL_MULT_ALTIMETER
(1.0):
-------------------------------------------------------------
Altimeter calibration constant:
PARAMETER: CAL_CONST_ALTIMETER
(0.0):
-------------------------------------------------------------
Inside Temp calibration multiplier:
PARAMETER: CAL_MULT_INTEMP
(1.0):
-------------------------------------------------------------
Inside Temp calibration constant:
PARAMETER: CAL_CONST_INTEMP
(0.0):
-------------------------------------------------------------
Outside Temp calibration multiplier:
PARAMETER: CAL_MULT_OUTTEMP
(1.0):
-------------------------------------------------------------
Outside Temp calibration constant:
PARAMETER: CAL_CONST_OUTTEMP
(0.0):
-------------------------------------------------------------
Inside Humidity calibration multiplier:
PARAMETER: CAL_MULT_INHUMIDITY
(1.0):
-------------------------------------------------------------
Inside Humidity calibration constant:
PARAMETER: CAL_CONST_INHUMIDITY
(0.0):
-------------------------------------------------------------
Outside Humidity calibration multiplier:
PARAMETER: CAL_MULT_OUTHUMIDITY
(1.0):
-------------------------------------------------------------
Outside Humidity calibration constant:
PARAMETER: CAL_CONST_OUTHUMIDITY
(0.0):
-------------------------------------------------------------
Wind Speed calibration multiplier:
PARAMETER: CAL_MULT_WINDSPEED
(1.0):
-------------------------------------------------------------
Wind Speed calibration constant:
PARAMETER: CAL_CONST_WINDSPEED
(0.0):
-------------------------------------------------------------
Wind Direction calibration multiplier:
PARAMETER: CAL_MULT_WINDDIR
(1.0):
-------------------------------------------------------------
Wind Direction calibration constant:
PARAMETER: CAL_CONST_WINDDIR
(0.0):
-------------------------------------------------------------
Rain calibration multiplier:
PARAMETER: CAL_MULT_RAIN
(1.0):
-------------------------------------------------------------
Rain calibration constant:
PARAMETER: CAL_CONST_RAIN
(0.0):
-------------------------------------------------------------
Rain Rate calibration multiplier:
PARAMETER: CAL_MULT_RAINRATE
(1.0):
-------------------------------------------------------------
Rain Rate calibration constant:
PARAMETER: CAL_CONST_RAINRATE
(0.0):
-------------------------------------------------------------
Seconds to wait before restarting a non-responsive process (0 disables):
PARAMETER: PROCMON_wviewd
(0):
-------------------------------------------------------------
Seconds to wait before restarting a non-responsive process (0 disables):
PARAMETER: PROCMON_htmlgend
(0):
-------------------------------------------------------------
Seconds to wait before restarting a non-responsive process (0 disables):
PARAMETER: PROCMON_wvalarmd
(120):
-------------------------------------------------------------
Seconds to wait before restarting a non-responsive process (0 disables):
PARAMETER: PROCMON_wvcwopd
(120):
-------------------------------------------------------------
Seconds to wait before restarting a non-responsive process (0 disables):
PARAMETER: PROCMON_wvhttpd
(120):
-------------------------------------------------------------
Destination address for email alerts:
PARAMETER: EMAIL_ADDRESS
(address@server.com): admin@leroeulxmeteo.no-ip.org
-------------------------------------------------------------
From address for email alerts:
PARAMETER: FROM_EMAIL_ADDRESS
(from_address@other_server.com): admin@leroeulxmeteo.no-ip.org
-------------------------------------------------------------
Send system alert emails?
PARAMETER: ENABLE_EMAIL_ALERTS
(no):
-------------------------------------------------------------
Send a test email?
PARAMETER: SEND_TEST_EMAIL
(no):
-------------------------------------------------------------
Admin Password (md5):
PARAMETER: ADMIN_PASSWORD
(71d6e40c9cdxxxxxxxxx9c214598f6): 71d6e40c9cd
xxxxxxxxx9c214598f6
################################################################################
--> wview Configuration Complete!
--> Now run wviewhtmlconfig to select your site skin.
################################################################################
root@raspberrypi:~#

ETAPE 6 : Configuration du style du site

wviewhtmlconfig
root@raspberrypi:~# wviewhtmlconfig
################################################################################
 !!!!!!!!!!!!!!!!         READ THIS BEFORE PROCEEDING         !!!!!!!!!!!!!!!!

--> HTML Template Configuration for wview

--> Note: This script will save existing templates to /etc/wview/html-YYYYMMDD.HHmmSS
          before writing the new files based on your answers here - if that
          is not what you want, hit CTRL-C now to abort this script!

################################################################################

pausing 5 seconds .....


---------------------------------------------------------------------------
Which template skin do you want to use for your site?

wview site skins currently supported:
    classic - default wview skin
    chrome  - classic with a chrome effect
    exfoliation - a clean implementation by Matthew Wall
(chrome):
Site skin chrome selected...
With NO extended data graphics.
With metric units.
Saving old HTML directory to html-20130904.220235 ...
...done.
Saving old config files...
... done.
cp: target `/usr/local/var/wview/img' is not a directory
HTML setup complete:
you may now customize template files in /etc/wview/html

ETAPE 7 - Les fichiers "template .htx" pour avoir votre site complètement en Français:
  ( fichier se trouvant sur une connection personnelle, et sur mon instance wview soyez donc patient )
 $ sudo wget http://leroeulxmeteo.no-ip.org/download/htx_FRENCH.tar.gz

$ tar -xzv htx_FRENCH.tar.gz  -C /etc/wview/html

 



ETAPE X - Mise à jour:


sudo apt-get update && sudo apt-get install raspi-config libraspberrypi*









EXEMPLE EN FRANCAIS :

http://leroeulxmeteo.no-ip.org

Source & Traduction de : https://docs.google.com/document/d/1HRJyqlyyQM84JW2t04f3XcNQT-P3KT53uo5pVQuwhVo/edit
Si vous désirez utiliser l'icone changée Raspi WVIEW :
$ sudo wget https://dl.dropbox.com/u/2427470/raspberry/wview/wview-100x100.png -O /var/lib/wviewmgmt/wview-100x100.png

30 commentaires:

  1. Merci pour ce beau tuto !
    La traduction est elle dispo ?

    RépondreSupprimer
  2. Oui, elle est dispo maintenant, une petite erreur de répertoire :

    http://leroeulxmeteo.no-ip.org/download/htx_FRENCH.tar.gz

    RépondreSupprimer
  3. Euh, j'ai une erreur 404 not found :s

    RépondreSupprimer
  4. Ca fonctionne maintenant, désolé.

    RépondreSupprimer
  5. Super, merci j'ai téléchargé le fichier :D
    Je suis encore un peu embetant mais je débute :

    en faisant la commande :$ tar -xzv htx_FRENCH.tar.gz /etc/wview/html

    rien ne se passe... meme en ajoutant le sudo...

    RépondreSupprimer
  6. Bonjour,
    Moi aussi en faisant la commande tar -xzv htx_FRENCH.tar.gz /etc/wview/html rien ne se passe. Pouvez vous me dire comment faire ?
    Merci
    Vincent

    RépondreSupprimer
  7. Bonjour et merci pour le tuto, très utile.
    J'ai moi aussi le probleme de l'installation des fichiers de traduction. La commande Tar reste muette et le Pi est bloqué...

    RépondreSupprimer
  8. Salut,

    Je souhaite utiliser la traduction de wview, mais manifestement le fichier htx_FRENCH.tar.gz n'est plus accessible (404). Est-il possible de le re-uploader ?
    Merci d'avance.

    RépondreSupprimer
  9. Eric, le fichier est à nouveau à disposition, peux-tu réessayer en utilisateur root.

    Jiembe, le fichier htx_FRENCH.tar.gz est à nouveau disponible.

    RépondreSupprimer
  10. Pour les personnes ayant des problèmes lors de la décompression de l'archive, veuillez utiliser la commande $ tar -xzv htx_FRENCH.tar.gz -C /etc/wview/html

    PS : le -C s'était perdu dans le copier/coller, désolé. ==> la procédure à été mise à jour

    RépondreSupprimer
    Réponses
    1. Salut.

      J'ai le problème malgré ce que tu as écrit.
      avec tar -xzv htx_FRENCH.tar.gz -C /etc/wview/html
      La console ne réagit pas.

      Une idée du problème?


      Supprimer
    2. J'ai réussi à le faire en détournant le problème.
      mkdir htm
      tar -xvf htx_FRENCH.tar.gz ./htm
      cp ./htm/*.* /etc/wview/html/

      Ceci dit, je me suis rendu compte que le tableau était vachement trop large. Et l’almanach est carrément parti en confettis. La page n'est pas affiché correctement. En fait il n'y a rien à voir avec l'original.

      Je suis repassé à la version originale du template.

      Pas grave dans la mesure où je n'ai besoin que du fichier.formateddata.txt pour l'utiliser depuis un autre serveur que lira les données, puis qui les transformera en TTS. Ainsi sur mon serveur VoIP j'aurai la météo locale sur mon téléphone.

      Supprimer
    3. Peut-être n'étais-tu pas en root pour faire le tar -xvf ?

      Oui les textes sont beaucoup plus longs en français qu'en anglais, et les pages doivent être adaptées.

      Supprimer
  11. C'est bon ça marche, merci beaucoup,

    RépondreSupprimer
  12. Bonjour.
    Bon tuto.
    A part que je galère un peu pour connecter la station WMR88 en USB.
    Visiblement, le port est /dev/ttyAMA0
    Mais je ne sais pas si je charge des données de la station.
    j'accède bien à la page de gestion, mais pas de page web de ma météo locale.
    du moins dans http://localhost/ rien.

    RépondreSupprimer
  13. bonjour, as tu configuré ton serveur web (apache) afin d'accéder aux pages générées par wview ? Créer un Alias est le plus simple

    RépondreSupprimer
  14. Non, je rien fait de tel.

    J'ai eu déjà l'occasion de faire un test sur une serveur sous Centos il y a quelques mois.
    Mais je ne souviens pas avoir fait quoi que ce soit sur apache.

    RépondreSupprimer
  15. En fait, j'ai des données dans http://...../weather/ mais aucun index.php, mais jes des fichiers png qui correspondent à des données de la station météo.
    Il ne manque pas un truc pour du genre, copier des fichiers d'un répertoire vers /var/www/ ?

    RépondreSupprimer
  16. Regardes si tu as bien le lien symbolique :
    $ sudo ln -s /var/lib/wview/img/ /var/www/weather

    Et après effectues un reboot du Raspberry, j'ai aussi ce bug, quand je crée des nouvelles pages, elles ne sont pas générées même avec un stop/start de wview mais seulement après un reboot.
    Si non, les traces sont dans normalement dans /var/log/messages pour voir si il y a des erreurs.

    RépondreSupprimer
  17. C'est bon ça fonctionne.
    Problème de cible sur les template et source html.

    Merci de ton aide

    RépondreSupprimer
  18. Bonjour,

    J'ai suivi l'ensemble de l'install qui et d'ailleurs bien fait, par contre j'ai un souci pour la traduction en français pas moyen de l'avoir ?
    Pouvez vous faire quelque chose a se niveau là ...
    Merci
    Bob

    RépondreSupprimer
  19. Bonjour à tous. Je galère pour récupérer les données de ma WRM200. En fait les services sont démarrés mais j'ai une erreur sur la génération des html : message : htlmgrInit failed!
    Merci pour votre aide et bravo pour votre boulot !

    RépondreSupprimer
  20. Bonjour, bravo pour ce travail. Je n'arrive pas à récupérer la traduction. Faut-il que Wview soit arrêté pour la récupérer et l'installer? Peut-on la récupérer sous Windows et la transférer après? Merci pour les réponses, je suis un grand débutant en Linux et Raspberry.

    RépondreSupprimer
  21. Bonjour, merci pour ce tuto qui ma permis d'installer ma station oregon (88) de partager mes données sur http://www.wunderground.com/personal-weather-station/dashboard?ID=IPOITOUC30#history tout en économisant sur l'éléctricité, mais j'ai 2 probèmes :
    le 1er c'est que je n'est pas accès depuis un ordi sur mon réseau a index.html (/etc/wview/html/index.html j'ai accès seulement à //monraspberry/wviewmgmt/*.*
    le 2ème, le cwop envois des trames vide y a t-il un autre logiciel pour envoyer du cwop avec un mot de passe sur un serveur de son choix Merci pour vaut réponses future

    RépondreSupprimer
  22. quand je vais surhttp://your_raspi_ip/wviewmgmt

    Ce site est inaccessible

    Impossible de trouver l'adresse DNS du serveur your_raspi_ip.
    Effectuez une recherche Google sur your raspi wview mgmt.
    ERR_NAME_NOT_RESOLVED

    merci de m'aider

    RépondreSupprimer